Verdict: useful for a run of matching cabinet hardware
The Kreg KHI-PULL is worth considering when several cabinet doors or drawer fronts need matching knobs or small pulls. Its value is repeatable setup: you decide the location once, then use the same reference edge and guide settings. It is less compelling for one simple hole or hardware outside its supported positions.
This is a research-based review of ASIN B01JQ74J5E, not a hands-on drilling test. We have not measured alignment error, guide wear or resistance to movement while clamped. The jig can organize a careful installation, but it cannot choose the correct layout or undo a hole drilled in the wrong place.
Reasons to consider it
- Repeatable edge reference for a series of parts
- Steel guides within a lightweight body
- Center position for knobs and paired positions for pulls
Trade-offs
- Drill, bit and clamp are extra
- Small-pull capacity needs checking before purchase
- Published guidance conflicts at 128 mm / 5-1/16 inches
Sources: Amazon: Kreg KHI-PULL, ASIN B01JQ74J5E, Kreg: Cabinet Hardware Jig KHI-PULL.
Facts: distinguish pull spacing from edge offset
Two measurements matter. Pull spacing is the center-to-center distance between the hardware’s mounting screws. Edge offset is how far the holes sit from the reference edge of the door or drawer. Kreg lists a 1–5-inch edge adjustment and several indexed inch pull positions. These are different settings, so a 5-inch offset does not establish compatibility with every 5-inch-long handle.
The basic kit supplies the jig components, not a complete drilling setup. Budget for a suitable clamp and a 3/16-inch bit. We retain the inch bit specification because the manufacturer manual and product page give inconsistent rounded metric equivalents.
| Reviewed model | Kreg KHI-PULL; ASIN B01JQ74J5E |
|---|---|
| Construction | Polymer body with hardened-steel drill guides |
| Edge offset | Manufacturer lists 1–5 inches to hole center |
| Indexed inch pull settings | 2.5, 3, 3.5, 4, 4.5 and 5 inches |
| Separate tools required | Drill, 3/16-inch drill bit and clamp |
| Included assembly | Base, edge guide, two drill guides, pads and adjustment hardware |
Sources: Kreg: Cabinet Hardware Jig KHI-PULL, Kreg: KHI-PULL North American owner’s manual.
Features: turn a chosen layout into a repeatable setup
The moving fence references the workpiece edge, while the drill guides establish the holes. For knobs, the guide moves to the center hole. For pulls, the manual shows matching the guide pointers and indexing features to the hardware’s center spacing. Secure the settings before repeating them across several fronts.
Our practical recommendation is to lay out the complete cabinet run first. Decide which edge each piece references and whether left- and right-hand doors need mirrored positions. A jig makes a chosen setting repeatable, including an incorrect setting, so test on scrap and hold the actual handle against the result before drilling finished fronts.
Raised trim and narrow rails deserve a physical fit check. Ask whether the fence can register squarely and whether a clamp can hold the base without tilting it. A tool that fits a broad flat drawer front may be less convenient on a decorative profile. Do not force a setup simply to use the jig.
Sources: Kreg: KHI-PULL North American owner’s manual, Kreg: Cabinet Hardware Jig KHI-PULL.
Research: the size boundary needs special attention
Kreg’s current specification table includes 128 mm pull spacing, while its product Q&A says 5-1/16-inch centers are unsupported. Those measurements are almost equivalent. We cannot resolve that conflict from the published page, so buyers at this boundary should confirm the exact supplied jig with Kreg rather than assume either statement applies.
For longer pulls or a wider variety of hardware, compare the separately identified Cabinet Hardware Jig Pro and its stated limits. The plain KHI-PULL should not inherit a newer model’s capacity. For one-off work, a carefully prepared template is another approach; for repeated jobs, consider whether the setup time saved justifies an additional tool.
Sources: Kreg: Cabinet Hardware Jig KHI-PULL, Kreg: Cabinet Hardware Jig Pro.
Safety: clamp the jig and protect the exit face
Follow the drill’s instructions and wear appropriate eye protection. The Kreg manual’s safety section tells users to clamp the jig rather than hold it by hand. Keep hands clear of the bit and the rear of the panel. Its non-slip pads do not remove the need for secure clamping.
The manual recommends clamping scrap wood behind the workpiece to reduce breakout as the bit exits. Protect the finished surface from trapped debris under the jig or clamp. Confirm what is behind an installed front, and remove or reposition the workpiece when necessary to keep drilling clear of surrounding components.
Sources: Kreg: KHI-PULL North American owner’s manual.
Buying: measure the hardware you actually own
Buy only after measuring screw-center spacing and checking that your cabinet profile offers a stable reference and clamping position. For replacement hardware, inspect existing holes before planning new ones; the jig does not conceal incompatible old spacing.
Confirm KHI-PULL, ASIN B01JQ74J5E and the basic package contents. Compare the total with the required drill bit and clamp, then review seller, delivery and return terms. Prices and stock vary. The current-offer link is useful only after the compatibility questions are settled.
Sources: Amazon: Kreg KHI-PULL, ASIN B01JQ74J5E, Kreg: Cabinet Hardware Jig KHI-PULL.
Related buying research
Compare a general drill guide and a measuring tool for cabinet-hardware layout.
Questions: avoid the common setup mix-ups
Does it include a drill bit or clamp?
No. Kreg specifies a separate 3/16-inch bit and a clamp, as well as your drill. Demonstration photos show accessories that are not part of the basic jig.
Can it install a single knob?
Yes. The manual places one drill guide in the center position for a knob. You still choose and mark the intended location.
Does it automatically center a drawer pull?
No. You establish the centerline and desired offset, then align and secure the jig. Repeated placement depends on preserving those settings and the same reference edge.
Will it fit a 128 mm pull?
Kreg’s specification table lists 128 mm, but its Q&A rejects 5-1/16-inch centers, approximately the same spacing. Confirm the actual supplied jig with Kreg before relying on this boundary size.
Can the guide prevent splintering by itself?
No. The manual advises a clamped scrap-wood backer where the bit exits. Material, bit condition and technique still affect the result.
Sources: Kreg: Cabinet Hardware Jig KHI-PULL, Kreg: KHI-PULL North American owner’s manual.
Sources and limitations
Research checked October 11, 2026. We checked the exact product identity against the primary sources below. Published specifications and seller imagery are not independent performance tests.
Sources: Amazon: Kreg KHI-PULL, ASIN B01JQ74J5E, Kreg: Cabinet Hardware Jig KHI-PULL, Kreg: KHI-PULL North American owner’s manual, Kreg: Cabinet Hardware Jig Pro.
Four genuine Kreg images show the basic jig and manufacturer demonstrations. Drills, bits and clamps are separate equipment. Repeated-position graphics do not establish our measured accuracy. Public-use image licensing remains unverified. Image-use disclosure.
Is this a hands-on review?
No. We have not measured performance, handling or durability. Product-specific evidence limits appear in the Research section.
Are these affiliate links?
Purchases through our retailer links may earn a commission. Disclosure and reader-rating privacy.
Image sources and context
- Basic KHI-PULL jig. Manufacturer product image; no hands-on test implied. Image provenance: kregtool.com
- Two-guide setup for pulls, as shown in Kreg’s original marketing graphic. Image provenance: kregtool.com
- Steel guide detail. The drill bit and clamp shown are separate equipment. Image provenance: kregtool.com
- Manufacturer drilling demonstration. Supply a drill, suitable bit and clamp separately. Image provenance: kregtool.com